Will A Ford Tonneau Cover Fit A Ram? (Explained)
Click Here To Check Recommended Tonneau Cover
We may earn commission from links on this page at no extra cost to you. We only recommend products we back!
Ford Tonneau covers are practical as a cargo management system; they come with unique designs that can help you categorize your truck bed.
But will a ford tonneau cover fit a ram? If you do not know, then read the whole article carefully.
Will A Ford Tonneau Cover Fit A Ram?
There is no definite answer to this question. Because it depends, some models of Ford will fit on a RAM, and some will not.

But adding a Ford Tonneau Cover to a RAM cargo can be a little tricky. Because these covers are hinged, hard material pieces are placed on the truck’s bed. But after adding, it provides maximum protection for your cargo.
If you want to get a Ford Tonneau Cover for your RAM cargo, be sure to match the size of the truck bed and the size of the Tonneau cover. If the size of the two matches, then you will be able to add it to your RAM cargo easily.
Read More: What Brand Tonneau Cover Does Ford Use
How to Install Ford Tonneau Cover in Ram
You may not consider the size of a truck bed until you need to purchase a tonneau cover for your vehicle. To install them, you must first verify both dimensions, which is a critical step that should not be overlooked. After verifying the size, follow the below steps. So, let’s get started without any delay!
Step 1
First, park your truck in a garage and note the size of the truck bed. To know the size of the truck bed, see the user manual where the size of the truck bed is specified.
If you do not have the user manual, you can use a measuring tape. You must know the size of the truck bed because you have to buy a Ford tonneau cover the same size. Or you should talk to an experienced person who can tell you the size of your truck bed without consulting the manual.
Step 2
Note the truck bed size when measured and convert inches to the desired unit. For example, if you want to convert from inches to feet, divide the length by 12.
Measure the width of the truck bed in the same way and then convert the unit in the same way. To measure the height, place the measuring tape on the top surface of the tailgate and place the other side on the bottom surface of the tailgate and convert the unit as well.
Read More: Does Ford Make A Tonneau Cover? Find Out Now!
Step 3
Now that you have finished measuring the truck bed repeat the same process and measure the Ford tonneau cover. Check if their sizes are the same. If the exact dimensions of the two are found, you can now begin the work of installing the tonneau cover.
Step 4
Now place the roll-up rails of the Tonneau cover on the right side of the truck bed and the other on the left side. Now attach the cover to the bulkhead and then to the front rail; attach the right end of the front rail to the right rail.
Step 5
Once the rails are set in place, you tighten the screws using a screwdriver. And in the same way, the left end of the front rail should be attached to the left rail, and the screws should also be tightened.
Now it’s time to fasten the clamp brackets, attach the right and left rails tightly to the truck bed, and make sure they are firmly in place. Check it by turning it towards the tailgate to see if you have fixed it properly with the Ram 1500 bed.
Step 6
If you want to secure your front rail, clean the bulkhead with a damp cloth. Then seal a bulkhead on top of the bulkhead. When the seal is firmly placed on the bulkhead, remove the seal protector on the upper surface.
Step 7
If you want to secure the front rail, first clean the bulkhead using a damp cloth and then place a bulkhead seal on top of the bulkhead. Once the seal is firmly placed on the bulkhead, remove the seal protector on its upper surface. Push the front rail down at the right angle and in the right position.
Step 8
If you have connected all its parts properly, now you can use the strap, pull the cover and see if it is working. If all goes well, then you’re done. You have succeeded in this task!
Install the Ford Tonneau cover on your RAM cargo car by following the above steps. If you are not an expert in this field, you must hire an expert.
Read More: Will A Chevy Tonneau Cover Fit A Ford?
Why Do You Need a Ford Tonneau Cover for RAM Cargo?
If you have a Ford truck with a RAM bed, then you need a tonneau cover. A tonneau cover protects your truck’s bed from weather and theft and increases your truck’s aerodynamics.
Even if you only use your truck for work or camping or hunting now and again, a tonneau cover will keep water from seeping in.
It will also keep you safe from theft since it secures your valuables in the vehicle’s bed. Your vehicle’s alarm system will sound if someone tampers with your ignition, making it more difficult for thieves to get in without being seen by you.
Not only do they provide excellent protection, but some of them also have an advanced locking mechanism that you must secure and feel confident will safeguard your belongings.
There are many different types of tonneau covers available on the market, so you’ll need to do some research to find the best one for your truck. But once you’ve found the perfect cover, you’ll be glad you made the investment!
Conclusion
When you choose a ford tonneau cover for your RAM cargo, you must be aware of the size. You will find many types of the ford tonneau cover in the market, but not all of them are suitable for your RAM.
So, before you buy, you must know the basics about that tonneau cover. We hope you have been able to find out by reading this article whether a ford tonneau cover will fit RAM cargo.